ASTM A530 PDF

1 Sep ASTM A/AM Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe. standard by ASTM. ASTM A PipeStandard cross-section and weight tolerances (ASTM A/ AM) NPS Outside Diameter (OD)¹ Wall Thickness (t)² Weight ³ Under Over. 1 Oct 20, and Section 21, are mandatory requirements to the ASTM 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel.

Author: Kagabei Gardagore
Country: Portugal
Language: English (Spanish)
Genre: Environment
Published (Last): 5 May 2017
Pages: 137
PDF File Size: 8.87 Mb
ePub File Size: 19.59 Mb
ISBN: 520-9-45783-851-6
Downloads: 99200
Price: Free* [*Free Regsitration Required]
Uploader: Goltiktilar

ASTM A530 Standard Specification

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

Combinging values from the two systems may result in nonconformace with the specification. Combining values from the two systems may result in nonconformance with the specification. It atsm the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

These designations refer to the latest issue of the respective specifications. Historical Version s – view previous versions of standard. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Most Related  STANAG 4123 PDF

ASTM A ASME SA Standard for General Requirements for Specialized Carbon and Alloy Steel Pipe

This specification covers a general requirements for specialized carbon and alloy steel pipe. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Defects in seamless pipe shall be repaired by welding.

Note 1-The dimensionless designator NPS nominal pipe size has been substituted in this standard for suchtraditional terms as “nominal diameter,” ” size,” and “nominal size. If the mechanical results asttm not conform to the requirements specified, retests shall be made. Within the text, the SI units are shown in brackets.

This abstract is a brief summary of the referenced standard.

The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Tensile tests, tension tests, flattening tests, hydrostatic tests and ultrasonic tests shall be made to conform to the ashm specified.

The inch-pound units shall apply unless the “M”designation SI fo the product specification is specified in the order.

ASTM A Standard Specification | Sunny Steel Enterprise Ltd.

This specification covers a group of requirements which, with the exceptions of Section 6. Within the text, the SI units are shown in brackert.

Combining values from the two systems may result in nonconformance with the specification. Carbon and Alloy Steel Pipe.

Leave a Reply Aztm reply Your email address will not be published.

ASTM A530 Standard for Specialized Carbon Alloy Steel Pipe

Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters. Your email address will not be published.

Most Related  OHIP DIAGNOSTIC CODES PDF

asmt

Tensile strength tests, tension tests, flattening tests, hydrostatic test and ultrasonic test shall be made to conform to the requirements specified. Link to Active This link will always route to the current Active version of the standard.

If the mechanical results do not conform to the requirements specified, retests shall be made. This abstract is a503 brief summary of the referenced standard. Work Item s – proposed revisions of this standard.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Defects in seamless pipe shall be repaired ast, welding.

Within the text, the SI units are shown in brackets. Defects in seamless pipe shall be repaired aetm welding. B Seamless pipe Marking. Tensile tests, tension tests, flattening tests, hydrostatic tests and ultrasonic tests shall be made to conform to the requirements specified.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Section 14 is for information only. In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied. If the mechanical results do not conform to the requirements specified, retests asgm be made.

You may use these HTML tags and attributes:

Author: admin