MP40 Data Sheet, application/pdf, MB, 08/06/ VorTech MP40w ES Propeller Pump Gen 2 MP40 Manual, application/pdf, MB, 10/27/ Your vortech propeller pump before you start, Adjust the pin spacer • Read online or download PDF • EcoTech Marine Gen 2 MP40 User Manual. MP40w ES. MP10 ES/ MP10w ES. For the full VorTech Pump manual, please visit our website at • Read this manual before installing .
|Published (Last):||16 August 2010|
|PDF File Size:||8.14 Mb|
|ePub File Size:||7.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
Go into Ecoech Mode by holding the Mode button for three seconds. Page 16 Page 17 – Section 3. Operational Modes At this point, you can press the set button to cycle through the different values that the current set- ting can be saved to. Maintenance Full Driver Memory Clear In order to clear out a saved wave you must perform a full memory clear on the master driver. Maintenance Maintenance General Manintenance Cleaning your VorTech The VorTech may manaul thorough cleaning of the components periodically to keep it running opti- mally.
Maintenance Page 36 – Section 6. Wireless Driver Firmware Upgrade Follow the instructions and diagram below to upgrade your drivers firmware. Table Of Contents Section 4. Troubleshooting Page 41 – Section 7.
Gently but firmly press down on the nozzle with your palm and twist coun- ter clockwise. Page 37 Upgrade Completed Successfully: While normally you cannot change the speed of a slave pump, because the speed is determined entirely by manjal master pump, with the EcoSmart driver you now have the ability to control the maxi- mum speed of individual slave pumps independently from the master. Adjust the pin spacer. The VorTech creates over 3, gallons per hour of low velocity flow within your aquarium.
Page 18 – Chapter 4: Please feel free to call or email us. Mp10’s Aren’t Just For Nano Tanks Ecohech Horizontal and vertical positioning of your pump on the glass With EcoSmart, we take the guess work out of where to place your pumps and how to make the most use out of our modes. Page 37 Page 38 – Section 6. Retry Firmware Upgrade Process.
In this mode, your Warranty Page ecotrch – Section 8. Slave pumps can only be set to sync or anti-sync modes, or the three options in EcoS- mart modes.
However, the precise position of any one pump on a pane of glass is still something which must be optimized to your particular aquarium. Short Pulse Mode can then be used if you would like a wave running all the time, or you can use an EcoSmart mode which will auto-load your saved wave frequency and use it during ecltech in the EcoSmart program.
This example would be the startup sequence for Firmware Revision 1. For this tank we recommend that you place the master pump running an EcoSmart mode on the right end of the back pane of glass, and a slave pump on the left side.
The EcoTech Marine Battery Backup sold separately combined with your VorTech pump is a unique accessory which greatly improves your likelihood of emerging from a power outage condition without any loss of livestock. Warranty If you notice a problem with your VorTech propeller pump, do not attempt to repair it yourself. Page 23 Short Pulse Mode can then be used if you would like a wave running all the time, or you can use an EcoSmart mode which will auto-load your saved wave frequency and use it during points in the EcoSmart program.
Ecotech Marine EcoSmart User Manual
Other Modes Page 27 Page 28 – Section 4. Follow the manua, and diagram below to upgrade your drivers firmware. For more information on each specific mode, see the full description of each mode in the next section of the manual.
The Configuration Menu is entered by pressing and holding all three buttons during any normal operational mode.
Follow these instructions to en- sure your pump is properly attached and will function properly. The nozzle should become free of the wet frame. Assigning Local Max Speed t You may setup a maximum of seven separate groups, each having a unique master pump.
Maintenance General Manintenance Cleaning your VorTech The VorTech may need thorough cleaning of the components periodically to keep it running opti- mally. This will come in handy if WWD driver to your new EcoSmart driver. Setup Your Vortech 5. The dim LEDs showing the speed setting.
For advanced EcoSmart pump positioning, see section 5.
Page 8 – Chapter 3: The following will guide you through navigating between each mode. The EcoSmart Wireless Driver enables wireless coordination and en- hanced functionality between multiple MP40w ES units right out of the box, with no extra equipment to buy—making it the most effective solution on the market for larger aquariums. Complain wrong Brand wrong Model non readable.
Lowest Speed of pump If none of this works, contact EcoTech Marine to speak with a service represenative.
Safety Warnings 2 this device must accept any interference including interference that may cause unde- sired operation of the device. Every product from EcoTech Marine is backed with our industry-leading customer service.
Page 29 Operational Modes At this point, you can press the set button to cycle through the different values that the current set- ting can be saved to. Don’t have an account?
During the firmware upgrade process, turn off all Wireless Wave Drivers and EcoSmart Driv- ers within feet of the two that you will be doing the upgrade process with. Use of this module in products not consented by EcoTech Marine is prohibited. Pump Configuration of EcoSmart Modes.