GLCD construction-pin description, power pins, control signals, block diagram, translating inputs on the screen; Graphic LCD interfacing. In order to proceed, as of to state the obvious, you need to get the GLCD arduino library from the arduino playground(there is also an. So in this tutorial we will interface KS GLCD with our Starter AVR board which has ATmega 32 micro controller on it. To learn more about this GLCD, visit .

Author: Kigakora Mikree
Country: Great Britain
Language: English (Spanish)
Genre: Relationship
Published (Last): 25 June 2011
Pages: 328
PDF File Size: 8.19 Mb
ePub File Size: 8.65 Mb
ISBN: 342-4-75067-183-5
Downloads: 61180
Price: Free* [*Free Regsitration Required]
Uploader: Doshicage

On a ks, the pot, which is typically between k, is used to create a varying negative voltage from Vee up to GND that is used to feed to the Vo input signal.

This parameter will be defined as Ecycle in the datasheet of the module. It is suggested that you wire up the panel using the default pin assignments. Related Hardware and Initiatives. This diagram shows wiring of the common type A panel. We will, at our option, either a repair the product using new or refurbished parts, or b replace the product with a new or refurbished product.

Ideally the command pins should all be on one port and all the data pins together on another. Starting with glcd v3, pin assignment is much more flexible as any glcd function or data pin can be assigned to any Arduino pin. This library is no longer being maintained by the authors and has not been updated since December In some display modules, this section may not be present.

RST ks00108 the reset pin, it is used to reset the entire display content by clearing whole of the display RAM. Only registered users can write reviews. While tempting to push wires or a 20 pin header into the holes without soldering, that will not create proper electrical connections.


The library is based on the excellent ks graphics routines written and copyright by Fabian Maximilian Thiele. Unlike a character LCD which can only display alphanumeric characters, a graphical LCD can display images, fonts and other structures.

Company Info About BuyDisplay. The software is called FontCreator2 and it can produce a header file that stores font definitions in program memory when included in your sketch. KS is a dot matrix display controller from Samsung with 64 channel output.

GLCD 128×64 display Graphic LCD Module w/KS0107+KS0108 Black on YG

The Arduino autoreset circuit is quit fragile. EastRising gives the promise to every customer to every product we sell on this web store.

Parts tamper ed with by grinding, engraving, drilling, cutting or applying coatings of any kind. To interface the graphical LCD, we need one 8-bit port and 6 other pins. All products are covered under our limited warranty, which provides all products are free of functional defects for a period of one year from the date of shipment and all products are free of visual defects and missing ke0108 for a period of 30 days from the date of shipment.

The interface has been made more Arduino friendly and some convenience functions added. The above table lists different instructions available for KS controller. By using a potentiometer, we can generate the required operating voltage by feeding the negative voltage to the Vo pin.

Warranty is void and no repair or replacement is granted under the following conditions:. Please, log in or register. The panel configuration is used to configure things that are specific to a particular glcd panel like the geometry of the display, the chip select lines, and the low level timing for the panel. Board Setup and Configuration.

Most Related  642-999 DCUCI EBOOK DOWNLOAD

Graphic LCD Library

At some point the Google Code site will probably be taken down completely. This library does not work with newer Arduino IDEs like the latest 1. The KS chip needs lots of pins. We can use a pot if you need to vary this too. It can be used in any embedded systems,industrial device,security,medical and hand-held equipment.

We have used a 1K resistor to limit the current to the backlit LED. Support for Arduino 1. We can vary Vo to change the contrast of the display. If you are ok with a GPL 3.

We use these pins to transfer the data to the display RAM. While any Arduino pin can can be used for any glcd data pin, using Arduino pins that are all in the same port and that are in consecutive bit order will give slightly higher performance.

GLCD glcd ks – Thunder-Wiring

See the documentation in the download for more information. The 19 and 20 pins are Anode and cathode of backlit LED, limit the current through it by putting a resistor in the line. Write Your Own Review Only registered users can write reviews. It is the master configuration file.

Author: admin